mad00046lem mn101e16 series type mn101e16k mn101e16y MN101EF16K mn101ef16z internal rom type mask rom flash rom (byte) 256k 384k 260k 512k ram (byte) 12k 20k 16k 30k package (lead-free) lqfp100-p-1414, qfp100-p-1818b qfp100-p-1818b lqfp100-p-1414, qfp100-p-1818b qfp100-p-1818b minimum instruction execution time 0.0588 s (at 2.7 v to 3.6 v, 17 mhz, at internal 2, 4, 8 times oscillation)) 0.1 s (at 2.7 v to 3.6 v, 20 mhz) 30.6 s (at 2.7 v to 3.6 v, 32.768 khz) ? interrupts reset. watchdog. external 0 to 5 . timer 0 to 3 . timer 6 . timer 7 (2 systems). timer a to e.time base. serial 0 (2 systems). serial 1 (2 systems). serial 2. serial 3 (2 systems). serial 4 (2 systems). automatic transfer ?nish (2 systems). a/d conversion ?nish. key interrupt ? timer counter 8-bit timer 10 timer 0 .................. square-wave/8-bit pwm output. event count. pulse width measurement. real time output control timer 1 .................. square-wave output. event count. synchronous output event timer 2 .................. square-wave/8-bit pwm output. event count. synchronous output event. pulse width measurement. real time output control. serial baud rate timer timer 3 .................. square-wave output. event count. serial baud rate timer timer 6 .................. 8 -bit freerun timer. time base timer timer a, b, c, d, e timer 0, 1 can be cascade-connected timer 0, 1, 2 can be cascade-connected timer 2, 3 can be cascade-connected timer 0, 1, 2, 3 can be cascade-connected 16-bit timer 1 timer 7 .................. square-wave/16-bit pwm output (cycle/duty continuous variable). event count. synchronous output event. pulse width measurement. input capture time base timer: one-minute count setting watchdog timer 1 ? serial interface synchronous type/uart (full-duplex) 3: serial 0, 1, 4 synchronous type/single-master i 2 c 1: serial 2 synchronous type/i 2 c 1: serial 3 ? dma controller number of channels: 2 channels maximum transfer cycles: 255 starting factor: external request. various types of interrupt. software transfer mode: 1 -byte transfer. word transfer. burst transfer ? i/o pins i/o 22 : (5 v i/f port) common use. speci?ed pull-up resistor available. input/output selectable (bit unit) 62 : (3 v i/f port) common use. speci?ed pull-up resistor available. input/output selectable (bit unit) 1 : (3 v i/f port) common use ? a/d converter 10-bit 8 channels (with s/h) ? special ports buzzer output. high-current drive port ? rom correction correcting address designation: up to 7 addresses possible
mad00046lem mn101e16k, mn101e16y, MN101EF16K, mn101ef16z ? pin assignment lqfp100-p-1414, qfp100-p-1818b sbo0a, txd0a, p0 0 sbi0a, rxd0a, p0 1 sbt0a, p0 2 sbo2a, sda2a, p0 3 sbi2a, p0 4 sbt2a, scl2a, p0 5 buzzer, p06 tm0io, p1 0 tm1io, p1 1 tm2io, p1 2 mmod osc2 osc1 vs s xi xo vdd3 3 vdd1 8 nrst , p2 7 tm3io, p1 3 tm7ioa, p14 tm7ob, p1 5 tm7oc, p1 6 sysclk, p1 7 irq0a, p2 0 p63, key3, a1 1 p62, key2, a10 p61, key1, a9 p60, key0, a8 p57, a7 p56, a6 p55, a5 p54, a4 p53, a3 p52, a2 p51, a1 vs s p50, a0 vdd1 8 p35, sbt3a, scl3a p34, sbi3a p33, sbo3a, sda3 a p32, sbt1 p31, sbi1, rxd1 p30, sbo1, txd1 p25, irq5 p24, irq4 p23, irq3 a p22, irq2 a p21, irq1 a p4 3 p42, sbt4 p41, sbi4, rxd 4 p40, sbo4, txd 4 p87, led7, d7 p86, led6, d6 p85, led5, d5 p84, led4, d4 p83, led3, d3 p82, led2, d2 p81, led1, d1 p80, led0, d0 vss p77, sd7, ndk p76, sd6, nwe p75, sd5, nre p74, sd4, ncs p73, sd3, a1 9 p72, sd2, a1 8 p71, sd1, a1 7 p70, sd0, a1 6 p67, key7, a1 5 p66, key6, a1 4 p65, key5, a1 3 p64, key4, a1 2 sbo0b, txd0b, p9 0 sbi0b, rxd0b, p9 1 sbt0b, p9 2 sbo3b, sda3b, p9 3 sbi3b, p9 4 sbt3b, scl3b, p9 5 sbo2b, sda2b, pd 0 sbi2b, pd 1 sbt2b, scl2b, pd 2 irq0b, pd 3 irq1b, pd 4 irq2b, pd 5 irq3b, pd 6 vdd 5 pd 7 vss an0, pa 0 an1, pa 1 an2, pa 2 an3, pa 3 an4, pa 4 an5, pa 5 an6, pa 6 an7, pa 7 vref+ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. no license is granted in and to any intellectual property right or other right owned by panasonic corporation or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805
|
